If you have the functional hood

DIVERSE BILDER VOM KITT UND KARR

If you have the functional hood scoop, then you will be able to tap into the hood scoop solenoid and use this 12 volt signal. Otherwise by installing a switch and tying one side to 12 volts and the output to the "Pursuit" wire, you can manually make the on board solenoid jump the LED light bars. The picture to the left shows the "Auto Cruise" lightbar on indicating you are using the "pursuit" function.

This new product also has the extra functions for "Cruise" telltale. If you have the factory option of cruise control, you can use the 12 volt signal coming from the turn-signal stem and use the LED display for the "Auto Cruise" readout. To make this work, you would have to use the factory service manual to find out the proper wire, but it normally is in the bundle coming from the steering column. And again, if you do not have the cruise option, then a 12 volt signal thru a momentary switch will function just as well.

This new product re-creates the visual effect of the highly recognized voice box where the audio voice came out in the tv show. It can be hooked up to your gm radio speaker and give a display for whatever audio is coming out of the speaker; cassette, radio, etc. The display board is available in two version, the red bargraph version, or the more "evil" yellow bar version. Both display versions can be used with the same driver board, so if you had the red and ever wanted to change to the yellow version, then you would be able to just purchase the yellow display board.

After producing the digital dash system for over 10 years and having many people inquire about various parts being made available as a separate item, Marks Custom Kits is now pleased to be able to offer the highly recognized voice display unit as a stand-alone item which does NOT need any other electronics to function and can be used in any car, truck or other visual application. Pictured left is the in-dash application currently being used. NOTE: All pictures on this page do not show the true clarity of the display board since photographing LEDs with lettering on them is very difficult to get the right combination of LED illuminance and detail. When the LEDs are on, the words are very clear and sharp and there is no problem reading the words or phrases.

SUPER HIGH-POWERED SCANNING LIGHT

The ultimate front bumper scanning light is finally here from the company that brought the high scanning light product to the consumer market; The Super High Power Scanner! This all new product will shine 5 times brighter than the standard scanner by using 60 watt halogen lamps, and an all new High Power Interface box that uses so much power to light these lamps, its needs a fan to keep the circuitry cool.

New Halogen Lightbar

This is the red light that is seen scanning back and forth in the front opening of the custom fiberglass nose. It is a custom made product that is bright enough to see in broad daylight and comes with a on/off speed control box, a high power interface box, and a custom made aluminum light bar. This is NOT a JC Whitney(R) light modified, but a custom designed light to meet the approval of the most demanding fan, including the trailing effect that everyone loves! It comes with a red lens but you can obtain any color Plexiglas you like to meet your needs and/or local motor vehicle requirements. The size of the lightbar is 23.5" long, by 1.25" high and 1.25" deep.

This new scanner still uses an on/off speed controller inside the car, but also uses the new Super High Power Interface to power the bright halogen lamps. These lamps will make you see spots if you stare at them. Will definitely grab the attention of everyone around you!

The new interface box, unlike the standard scanner, has a fan to keep the circuitry cool, and must be located where ample airflow can help keep the electronics operating at optimum capacity. It can be mounted under the radiator shroud for water protection. It is pictured here for clarity.

This new scanner is a very high power consuming device and caution must be used while operating it. The halogen lamps and aluminum light-bar get very hot during use. Due to the power consumption, it is advisable to run the car occasionally while at static car shows to keep your battery up to proper cranking charge. And because of the physical properties of halogen lamps, they are more sensitive to vibration and therefore are not designed for rough road handling, bouncing or extreme jarring.